The ZX-24t the low power version of the ZX-24s microcontroller.
Since it is largely source code compatible with the ZX-24s, it provides an excellent alternative for applications requiring lower power consumption. It can run at a supply voltage as low as 2.7 volts.
The heart of the ZX-24s is the Atmel AVR ATmega1284P microcontroller running at 7.37MHz.
It is accompanied by some support circuitry on a 24-pin DIP module that is
pin-compatible with the ZX-24s, the Parallax Basic Stamp and the NetMedia BX-24 microcontrollers.
The ATmega1284P microcontroller internally has 16384 bytes of RAM and 4064 bytes of EEPROM available for your programs.
The 128K byte internal Flash memory of the mega1284P is partially occupied by special serial downloader firmware leaving 124K bytes of Flash memory for your programs.
The mega1284P has other resources available to your program including two high-speed serial ports,
analog-to-digital converters, timers and other sub-systems that may be accessed using
routines in the ZBasic System Library. Alternately, some of these resources may be accessed
directly using built-in registers.
You may download a schematic of the ZX-24t (identical to that of the ZX-24 except for there being no serial EEPROM) as a
PDF
or as an ExpressPCB .sch file.
To view the latter, you'll have to download free software from
ExpressPCB.
ZX-24t Technical Features¹
| Package |
24-pin DIP |
| Operating Temperature |
-40 to +85°C |
| Processor |
Atmel AVR ATmega1284P |
| Power Requirements |
2.7-5.5VDC regulated |
| Processor Speed |
Up to 7.37MIPS (7.37MHz) |
| Program Execution Speed |
Up to 1.5 million instructions/sec² |
| User RAM |
16K bytes |
| Non-volatile Data Memory |
4064 bytes |
| Program Memory |
124K bytes |
| Digital I/O pins |
16+3³ |
| Analog-to-Digital Channels |
Up to 8 channels, 10-bit resolution |
| PWM Channels |
Four 16-bit, two 8-bit |
| I2C Support |
1 HW channel, 4 SW channels |
| 1-Wire Support |
Bit and byte level |
| SPI Support |
4 HW channels |
| Synchronous Serial I/O Support |
1-16 bits, MSB or LSB first |
| Asynchronous Serial I/O Ports |
2-HW, up to 4 SW full duplex |
| X-10 Command Support |
Yes |
| Multi-tasking Support |
Yes |
| External Interrupts |
3 |
| Pin Change Interrupts |
All I/O lines |
| Analog Comparator Interrupt |
Yes |
| Interval Timer |
Yes |
| Exception Handling Support |
Yes |
| Floating Point Math |
Yes - IEEE 32-bit |
| Advanced Floating Point
Functions (sin, cos, log, etc.) |
Yes |
| Programming Interface |
Serial - 115.2K baud |
| Field Upgradeable System Software |
No |
| Supports Inline Assembly Code |
Yes |
| Supports Interrupt Handling Code |
Yes |
Notes:
1) Items in boldface indicate differences from the ZX-24s.
2) Speed based on the instruction b = b + 1.
3) The additional 3 I/O lines are outside of the standard 24-pin DIP format.
Specifications subject to correction and change without notice.
|
A standard serial port is required to download code to the ZX-24t.
If your computer does not have a standard 9-pin serial port but does have a USB port, you may use a USB to serial adapter.
Note, however, that some USB to serial adapters are too slow to be useful with the ZX microcontrollers.
We have found that adapters based on the second generation FTDI chips seem to work well.
